Artificial turf is widely used in baseball, rugby, football, hockey, softball, athletics and other sports fields.
fields, athletic fields and other sports fields, as well as playgrounds, practice fields, sports classes, military training and other indoor and outdoor activities.
It is also ideal for playgrounds, practice fields, sports classes, military training and other indoor and outdoor activities. What are the specifications for the construction of artificial turf?
ZHONGSHAN DOLEUNGCHOI PLASTIC TECHNOLOGY Company is the answer to your questions, hopefully it will help you.
We hope you find this helpful.
Check And Accept The Foundation Works Of Artificial Grass Yarn
Clear the foundation of debris, if there is unevenness, should be timely repair, leveling. Construction
The construction site must be clean to ensure a clean environment and construction quality.
Measurement And Proofing Of Artificial Grass Yarn
1.To carry out the measurement and proofing according to the plan of the design.
2.Use a latitude and longitude meter or other precision measuring instruments to measure whether the surrounding facilities conform to the dimensions of the sports ground.
The dimensions of the sports ground. Any unsuitable areas should be modified immediately, with a tolerance of 5 mm.
- Pavement
Lay the turf on the ground according to the original specification, with 3~8mm lap between the turf.
Cut the overlapping turf flush with a turf cutter. The joints should be no larger than 3mm.
Lay the lap cloth under the cut area and use a glue applicator to apply a jointing agent to the jointed surface. Brush the jointing glue onto the joint surface, touching it with your fingers.
After drying the joint is tapped firmly.
Turf Bonding Construction Process Instructions
1.The turf base and interface cloth to be bonded must be clean and the surface dry and free of
Water.
2.The ambient temperature should be selected in 5 ° C above construction is appropriate, and should not be in the rain and mouldy rain
Otherwise it will lead to long bonding time or even bow|up non-stick phenomenon.
The Specific Construction Process
1.Glue application: require the use of glue applicator in the surface coating thickness uniform, not repeatedly coated with glue,
Otherwise there will be blistering and even falling. Undercloth using the glue applicator, strict control of the glue
The thickness, pay attention to the speed of the glue should be appropriate, the glue should be applied to the two bonded surfaces respectively.
2.Sticky and: according to the temperature, humidity, air pressure and other conditions at the time of the actual impact, reasonable control of drying time.
Control the drying time reasonably. Generally within 10-30 minutes after the application of glue, the glue paste reaches 80-90% dry.
The glue should not be sticky to the touch. When gluing, it is important to align the adhesive firmly at once and not to move the glued object back and forth after gluing.
Move the object to be bonded.
3.Pressure: after the bonding, clear its surface debris, with a special rubber hammer from the sticky
The joint to both sides of the force hammer solid, so that its surface fully contact dense, bonding more firmly.
4.Curing: its curing time is generally three days, testing the final strength is generally ten days.
During the curing period should pay attention to maintenance, avoid exposure to the sun, water and movement, has reached the best bonding state.
5.After bonding, before spreading quartz sand and rubber granules, the field needs to be cleaned with imported cleaners.
The cut pieces of turf should be cleaned with an imported cleaner.
Construction Precautions
1.Construction, do not expose the adhesive for too long, because the solvent volatilization will cause adhesion
The solvent will evaporate and cause too much adhesion and cannot be constructed.
2.If the temperature is too low, hot water can be used to warm up to 15 - 20°C, then the original state can be restored.The original state and performance remains unchanged.
Spreading Of Quartz Sand Grit And Rubber Granules:
1.Spreading shall be carried out with a spreading machine. The quartz sand must be more than 80% round.
Round diameter 0.2 to 1.5mm.
2.The quartz sand and rubber granules can only be laid after the artificial turf field material has been installed.
grains.
3.The laying of quartz sand should be injected in N times according to the designed sand quantity.
The quartz sand must be repeatedly combed with professional combing equipment to make the quartz sand fall sufficiently dense. Any impurities found in the paving
Any impurities found in the paving must be removed immediately to ensure quality.
4.The quartz sand must be checked for levelness and adequacy and any deficiencies must be filled in as appropriate.
5.Fill the quartz sand with rubber granules in the same way as the quartz sand paving.
