Perhaps you have purchased and used an incredible oxygen compressor? In actuality, even if it is actually simple, using an oxygen compressor is not an easy task. However, the maintenance while using oxygen compressor is important.
Main:

How to hire an oxygen compressor?

O2 compressor program maintenance and precautions

To conclude

Easy methods to make use of an oxygen compressor?

Using an oxygen compressor just isn't as complicated as you could possibly think, it's actually easy. After the compressor can be installed, it can often be place in normal procedure after standard test. If you wish to adjust a parameter, you might want to follow the steps down below:

1. Pressure switch setpoint move about

The machine usually capabilities 2 pressure switches. Finding the one you could adjust not only needs to learn how to use the oxygen compressor, as well as the maintenance of the precise oxygen compressor, because it relates to normal use. Control standard principle: Loading pressure (starting pressure) + differential kind = stop pressure.

l When adjusting, take the pressure gauge because standard and loosen this particular tightening nut;

l Limit the loading pressure: turn the pressure adjusting twist clockwise (pointer up, pressure decrease) for half seven days, observe whether the launching pressure meets certain conditions (because the pressure difference isn't adjusted, the stopping requirement will change accordingly), if not, adjust it appropriately.

l Add to the pressure difference: rotate the particular differential pressure adjustment connect counterclockwise (the pointer changes down, the pressure difference increases) for half One week, and observe whether the pressure difference will be the stop pressure or not likely, if no adjustment will be created.

l After each and every strain value is reset to zero, lock the nut plus correct the parameters as soon as. Increase the loading demand or reduce the force difference plus reverse that adjustment because described on top of. The inlet pressure switch adjustment method is in fact the same, but the wiring method takes a new approach, the stop strain currently = starting strain - differential pressure. It truly is strictly forbidden to perform the device above this rated exhaust pressure.

COUPLE OF. Heat controller adjustment

Each stage with the compressor gives you some sort of temperature controller, and that is installed for the control cabinet panel and it is set at the developing plant.

Set it, in case you should reset, please refer into the manual of the brilliant temperature controller.

3. Power relay regulation

The thermal relay acts being a motor overload protection. Occasionally, the motor will conclusion rotating. If the set value is thought he would be malfunctioning, it needs to be properly adjusted by expert electric work, and the running current need to be measured. When the compressor may be working normally, there is less work to get maintained, but it really needs to be handled by a particular person. It should be patrolled twice per shift to see whether the compressor possesses abnormal heat, abnormal vibration, unnatural sound, etc. If it is critical, stop it immediately. Without delay after confirming the troubleshooting, it is possible to continue to run. When they get home of just about every shift, the ability should be turned off combined with intake valve closed. In an attempt to ensure long-term reliable operation while in the machine, it must regularly be checked regularly.

Oxygen compressor plan maintenance and precautions
TRUE. When the compressor is unquestionably running, it must properly do necessary inspections in addition to inspections, monitor the operating conditions about the compressor, closely monitor this kind of suction, exhaust pressure and also temperature, exhaust volume, cooling water temperature and various control indicators, pay specific attention to abnormal sound, and Record every every now and then.

2. During the functioning, the process gas might be strictly prevented from being crushed in the low-pressure cylinder and other gas pipelines because the high-pressure cylinder to avert oil, water and h2o.

3. It is forbidden to control the compressor under over-temperature, over-pressure as well as over-speed. If there can be any abnormality, you should carefully clear away the fault and report it in time.

4. Gas leakage Once the vehicle is within catastrophe stop, the power needs to be cut off in the specific substation.

5. When repairing the equipment, carefully check the maintenance license as well as the relevant safety inspection regulations to be assured the safety of this particular inspection.

6. When applying an oxygen compressor, usually do not use oily sand to wipe the gear, pipes, valves and elements. Do not be afflicted by oil. Degreasing treatment really should be carried out after examination, and flammable gas leakage monitoring equipment have to be provided.

7. Check the cutter room and arbitrarily number flammable materials.

In decide on

You don't have to fret about the caliber from the compressor, because your oxygen compressors, nitrogen compressors, CARBON compressors, etc. have passed the EU CE certification and so are also recognized for the safety inside the compressor. If you still don't learn how to use it, you can certainly help consult us. But make sure to pay attention to safeguards work.
i loved this
201911ld